Gutters cost in Sioux City, IA
Local estimate from BLS wage data and BEA price levels. Reviewed Nov 4, 2026.
- Typical range (160 linear ft)
- $1,250 – $4,000
- Per linear ft
- $7.75 – $24
- before permit
- Versus US midpoint
- −4%
- US $2,750
- Rank of 300 metros
- #155
- 1 = most expensive
If you want to install gutters in Sioux City, plan on $1,250 to $4,000 for 160 linear ft, all in. Per linear ft, that is $7.75 to $24 for materials and labor, with the permit on top. The local midpoint runs 4% lower than the national one. Building materials run about 6% below the US average here (BEA goods price index 94.0).
Estimate your gutters cost
Pick a size, a quality level and where you live. Prices update as you type.
Estimated cost for 160 linear ft in Sioux City, IA, standard level
$2,100 to $3,200
About $12.50 to $19 per linear ft before permits. Labor is about 40% of the bill.
| Part | Low | High |
|---|---|---|
| Materials | $1,150 | $1,850 |
| Labor | $880 | $1,200 |
| Permits and fees | $50 | $120 |
| Total | $2,100 | $3,200 |
Cost breakdown for 160 linear ft in Sioux City, IA
| Part of the job | Low | Midpoint | High | Share |
|---|---|---|---|---|
| Materials | $600 | $1,500 | $2,400 | 57% |
| Labor | $640 | $1,050 | $1,450 | 40% |
| Permits and fees | $0 | $85 | $170 | 3% |
| Total | $1,250 | $2,650 | $4,000 | 100% |
Where the Sioux City price comes from
Labor is 40% of the midpoint bill here, against 38% nationally. The mix of trades behind this job is sheet metal workers (40%), roofers (30%), construction laborers (30%). We weight each trade's local median wage by that share and compare it with the national median. In Sioux City the blended ratio comes out at 1.00.
On the materials line, the BEA goods price index for the Sioux City metro is 94.0 (US = 100). The midpoint materials bill for 160 linear ft comes to $1,500, compared with $1,600 at national prices. Permit and inspection fees are scaled by the broader index (86.5) and land at $0 to $170.
Climate in Sioux City: timing your gutters job
We use NOAA's 1991-2020 climate normals for Sioux City Gateway Ap (5 miles from the city center). These are 30-year monthly averages, not forecasts.
March through November is the stretch where exterior installation runs into the fewest weather problems in Sioux City (9 of 12 months). January, February and December have an average daytime high under 45°F.
In January, February and December the average high stays below 45°F. Sealants, adhesives and some materials, such as vinyl, are harder to install well in the cold, and short daylight cuts the working day.
Sioux City gets about 29 inches of precipitation in a normal year, including roughly 36 inches of snow. The wettest months are May, June and August (4.3 inches in June). Inside the workable window, March and November are the driest, at 1.8 and 1.3 inches. The station averages about 25 days a year at 90°F or above.
Does the season change the price? Probably, but we do not have a sourced seasonal price curve, so the estimator shows a year-round figure and does not adjust by month. When you collect quotes, ask whether scheduling in a slower month gets a better rate.
| Month | Avg high °F | Avg low °F | Precip (in) | For this job |
|---|---|---|---|---|
| Jan | 30 | 10 | 0.7 | Cold |
| Feb | 34 | 15 | 0.9 | Cold |
| Mar | 48 | 26 | 1.8 | Workable |
| Apr | 61 | 37 | 3.1 | Workable |
| May | 72 | 49 | 3.9 | Workable |
| Jun | 82 | 59 | 4.3 | Workable |
| Jul | 85 | 63 | 3.4 | Workable |
| Aug | 83 | 61 | 3.9 | Workable |
| Sep | 77 | 51 | 2.8 | Workable |
| Oct | 63 | 38 | 2.2 | Workable |
| Nov | 47 | 25 | 1.3 | Workable |
| Dec | 33 | 15 | 1.0 | Cold |
Planning more than one job in Sioux City?
Because every project leans on different trades, Sioux City's wage level does not move all prices equally. Against the US midpoint, French drain runs −1% and roof replacement −10%.
| Project | Size | Range | vs. US |
|---|---|---|---|
| Roof replacement | 2,000 sq ft of roof | $5,450 – $11,300 | −10% |
| Metal roof | 2,000 sq ft of roof | $9,350 – $30,100 | −7% |
| Vinyl siding | 2,100 sq ft of wall | $7,850 – $23,500 | −7% |
| French drain | 60 linear ft | $590 – $2,100 | −1% |
| Attic insulation | 1,000 sq ft | $970 – $3,850 | −4% |
Why two Sioux City quotes can differ
Stories
Two-story homes add $1-$3 per linear foot for ladders and fall protection.
Permit
Local building codes may add $50-$200, though most cities don't require one.
Material
Vinyl is $8-$12 per linear foot installed and aluminum $10-$20. Steel and copper run higher (HomeGuide).
Sioux City labor market for gutters
Wages are the part of this estimate that changes most from town to town. 3 trades carry the job here, and each is compared with its US median. The weighted result for Sioux City is 1.00 times the national level.
For sheet metal workers (47-2211, weighted 40%) the local median is $32.38 an hour, which is 9% above the national $29.71. The middle half of them earn between $22.42 and $36.63 an hour. BLS counts 50 of them working in the area, 6.7 for every 10,000 jobs (US: 7.7), so the local bench is about average.
For roofers (47-2181, weighted 30%) the local median is $22.62 an hour, which is 15% below the national $26.65. The middle half of them earn between $18.46 and $27.56 an hour. BLS counts 90 of them working in the area, 12.0 for every 10,000 jobs (US: 8.7), so the local bench is deeper than average.
Construction laborers (47-2061), 30% of the weighting: a median of $23.38 an hour, 3% above the US median of $22.66. The middle half of them earn between $21.71 and $28.72 an hour. About 560 work in the metro. That is 74.7 per 10,000 jobs, compared with 70.5 nationally, so the supply of crews looks typical.
Quotes come from real crews, not medians. If the sheet metal workers on your job are paid at the 75th percentile ($36.63 an hour) instead of the median, the labor line grows by about $60. At the 25th percentile ($22.42) it shrinks by about $140. The total moves by 2.3% or 5.3%, so wages alone rarely explain a quote that is far outside our range.
For context on the local economy, BLS counts 75,010 jobs in the Sioux City area. That makes it the 247th largest of the 300 metros we cover, with 0.05% of US employment.
| Trade | Weight | 25th pct | Median | 75th pct | US median | Ratio | Level used |
|---|---|---|---|---|---|---|---|
| Sheet metal workers (47-2211) | 40% | $22.42 | $32.38 | $36.63 | $29.71 | 1.09 | metro |
| Roofers (47-2181) | 30% | $18.46 | $22.62 | $27.56 | $26.65 | 0.85 | metro |
| Construction laborers (47-2061) | 30% | $21.71 | $23.38 | $28.72 | $22.66 | 1.03 | metro |
| Blended | 100% | 1.00 | |||||
How Sioux City compares
Of the five closest metros, 3 are cheaper than Sioux City. Lincoln is the lowest at about $2,550 (midpoint, 160 linear ft), 120 miles away.
| Area | Range | Midpoint | vs. here |
|---|---|---|---|
| Sioux City, IAthis page | $1,250 – $4,000 | $2,650 | |
| Sioux Falls, SD75 miles | $1,150 – $3,900 | $2,550 | −4% |
| Omaha, NE85 miles | $1,250 – $4,100 | $2,700 | +2% |
| Lincoln, NE120 miles | $1,200 – $3,900 | $2,550 | −4% |
| Des Moines, IA145 miles | $1,250 – $4,050 | $2,650 | +1% |
| Waterloo, IA195 miles | $1,250 – $4,000 | $2,600 | −1% |
| Iowa (statewide) | $1,250 – $4,000 | $2,650 | level |
| United States | $1,300 – $4,200 | $2,750 | +4% |
Across 300 US metros, Sioux City comes in at #155 from the top. The priciest is San Francisco, CA at $3,450; the cheapest is Longview, TX at $2,350 (midpoints, 160 linear ft). Statewide, Sioux City is 0% above the Iowa figure.
Other Iowa metros
| Metro | Size | Range | Midpoint | vs. here |
|---|---|---|---|---|
| Des Moines, IA | 404,130 jobs | $1,250 – $4,050 | $2,650 | +1% |
| Davenport, IA | 180,450 jobs | $1,300 – $4,150 | $2,700 | +3% |
| Cedar Rapids, IA | 139,260 jobs | $1,300 – $4,150 | $2,750 | +4% |
| Iowa City, IA | 93,760 jobs | $1,250 – $4,000 | $2,650 | level |
| Waterloo, IA | 84,260 jobs | $1,250 – $4,000 | $2,600 | −1% |
| Dubuque, IA | 58,470 jobs | $1,250 – $4,000 | $2,650 | level |
Cities with a workforce like Sioux City's
Big cities and small ones price differently, so here is Sioux City against the 4 metros with the closest total employment.
| Metro | Size | Range | Midpoint | vs. here |
|---|---|---|---|---|
| Abilene, TX | 75,070 jobs | $1,100 – $3,700 | $2,400 | −9% |
| Blacksburg, VA | 74,070 jobs | $1,100 – $3,750 | $2,450 | −7% |
| Kenosha, WI | 75,450 jobs | $1,400 – $4,550 | $3,000 | +14% |
| Rapid City, SD | 73,820 jobs | $1,150 – $3,800 | $2,500 | −6% |
Pick a size, pick a tier: gutters pricing in Sioux City
Three bands are cut from the same cited range and localized for Sioux City wages and prices. They overlap on purpose: a good standard job and a modest premium job can cost the same. The grid below prices the same bands at 3 common sizes.
Basic
$1,250 to $2,350
Vinyl or sectional aluminum, single story
Standard
$2,100 to $3,200
Seamless aluminum K-style, standard downspouts
Premium
$2,900 to $4,000
Steel or copper, two stories, custom length
| Size | Basic | Standard | Premium |
|---|---|---|---|
| small house (120 linear ft) | $930 – $1,800 | $1,550 – $2,400 | $2,200 – $3,050 |
| average house (160 linear ft) | $1,250 – $2,350 | $2,100 – $3,200 | $2,900 – $4,000 |
| large house (240 linear ft) | $1,850 – $3,500 | $3,100 – $4,700 | $4,300 – $5,950 |
Get 3 local quotes
Tell us about the job and we will try to connect you with up to three local contractors for written quotes. It is free and you are under no obligation to hire. Your estimate of $2,100 to $3,200 for Sioux City, IA is attached.
Detailed gutters report for Sioux City, IA, $9
Multi-page report for Sioux City, IA: low, typical and high cost, a line-item breakdown of materials and labor by trade, permit notes, the best months to schedule, a quote comparison sheet, red flags, questions for contractors, checklists and every source. Save your estimate above, preview page 1 free, and unlock the full report for $9 one-time, or get every report with CostLocal Pro.
Gutters in Sioux City: your questions
+How much does it cost to install gutters in Sioux City?
For 160 linear ft, expect $1,250 to $4,000 in the Sioux City area. A standard-spec job lands at $2,100 to $3,200. Small jobs usually cost more per linear ft and large ones less.
+What is the price per linear ft for gutters in Sioux City?
About $7.75 to $24 per linear ft for materials and labor, plus $0 to $170 for the permit if one is needed. The US range is $8 to $25.
+Is gutters cheaper in Sioux City or Sioux Falls?
Sioux Falls is 75 miles away. The midpoint for 160 linear ft there is $2,550, which is 4% less than Sioux City ($2,650). Wage and materials indexes both feed that gap.
+How much of the bill is labor in Sioux City?
About 40% at the midpoint, or $1,050 out of $2,650. Materials are 57% and permits 3%. Nationally, labor is 38%.
+What would average house (160 linear ft) cost in Sioux City?
$1,250 to $4,000. Pick a different size in the estimator above to get your own number.
+Does gutters need a permit in Sioux City?
Often, but rules are set by your city or county building office, so call before you hire. Budget $0 to $170 for fees in the Sioux City area (our national range of $0 to $200 scaled by the local price level).
+Is Sioux City expensive for gutters compared with the rest of Iowa?
Sioux City is 0% above the Iowa statewide estimate ($2,650 at the midpoint). We cover 7 metros in Iowa; see the state page to compare them.
+What do sheet metal workers earn in Sioux City?
The BLS median is $32.38 an hour in the Sioux City area, compared with $29.71 nationally. The 25th to 75th percentile range is $22.42 to $36.63.
+What do basic and premium gutters work cost in Sioux City?
For 160 linear ft, basic work runs $1,250 to $2,350 and premium work $2,900 to $4,000. Basic means: vinyl or sectional aluminum, single story. Premium means: steel or copper, two stories, custom length.
+When is the best time to install gutters in Sioux City?
Based on NOAA 1991-2020 normals, the comfortable months for this kind of work are March through November. March and November are typically the driest of those months. Local contractors' schedules matter as much as the weather, so book early for the busy months.
Gutters near Sioux City
Where these numbers come from
Base prices are national ranges from the sources below. We scale labor by local BLS wages, materials by BEA goods prices and permits by the BEA all-items price level. Full method on the methodology page.
- HomeGuide: How Much Does Gutter Installation Cost? (2026) (accessed November 4, 2026)
- Home Genius Exteriors: How Much Does Gutter Installation Cost? (accessed November 4, 2026)
- BLS Occupational Employment and Wage Statistics, May 2025
- BEA Regional Price Parities, 2024
- NOAA NCEI U.S. Climate Normals, 1991-2020
Note on derived figures: Materials = installed range minus the $4-$9 per linear foot labor figure from Home Genius Exteriors.