Skip to content
CostLocal

Aluminum fence cost in Coeur d'Alene, ID

Local estimate from BLS wage data and BEA price levels. Reviewed Nov 4, 2026.

Typical range (150 linear ft)
$3,650 – $10,900
Per linear ft
$24 – $72
before permit
Versus US midpoint
−4%
US $7,600
Rank of 300 metros
#154
1 = most expensive

Coeur d'Alene homeowners pay roughly $3,650 to $10,900 to install an aluminum fence at 150 linear ft, or $24 to $72 per linear ft (permit not included). Against the US midpoint, Coeur d'Alene is 4% lower. Building materials run about 4% below the US average here (BEA goods price index 96.2).

Estimate your aluminum fence cost

Pick a size, a quality level and where you live. Prices update as you type.

Quality level

Ornamental pool-code fence, 4-5 ft

Add-ons

Estimated cost for 150 linear ft in Coeur d'Alene, ID, standard level

$5,800 to $8,750

About $38.50 to $57.50 per linear ft before permits. Labor is about 34% of the bill.

Cost breakdown
PartLowHigh
Materials$3,700$5,700
Labor$2,050$2,950
Permits and fees$70$120
Total$5,800$8,750
Save and get a PDF report

Cost breakdown for 150 linear ft in Coeur d'Alene, ID

Part of the jobLowMidpointHighShare
Materials$2,150$4,700$7,20064%
Labor$1,450$2,500$3,55034%
Permits and fees$40$95$1501%
Total$3,650$7,300$10,900100%

Where the Coeur d'Alene price comes from

Labor is 34% of the midpoint bill here, against 35% nationally. The mix of trades behind this job is carpenters (40%), construction laborers (40%), sheet metal workers (20%). We weight each trade's local median wage by that share and compare it with the national median. In Coeur d'Alene the blended ratio comes out at 0.95.

On the materials line, the BEA goods price index for the Coeur d'Alene metro is 96.2 (US = 100). The midpoint materials bill for 150 linear ft comes to $4,700, compared with $4,900 at national prices. Permit and inspection fees are scaled by the broader index (98.3) and land at $40 to $150.

Data note: 20% of the labor weighting for this project uses a statewide median because BLS has no published metro figure for that trade in Coeur d'Alene. The wage table below marks each row.

Coeur d'Alene against nearby metros and the rest of Idaho

Same job, same size (150 linear ft), priced for the nearest metros. Seattle is the priciest of the group at $8,750.

Comparison with nearby areas
AreaRangeMidpointvs. here
Coeur d'Alene, IDthis page$3,650 – $10,900$7,300
Spokane, WA55 miles$4,050 – $12,100$8,050+11%
Missoula, MT120 miles$3,700 – $11,100$7,400+2%
Kennewick, WA150 miles$4,200 – $12,500$8,350+15%
Yakima, WA210 miles$4,050 – $12,100$8,050+11%
Seattle, WA240 miles$4,450 – $13,100$8,750+20%
Idaho (statewide)$3,550 – $10,700$7,150−2%
United States$3,800 – $11,400$7,600+4%

Across 300 US metros, Coeur d'Alene comes in at #154 from the top. The priciest is Honolulu, HI at $9,700; the cheapest is Brownsville, TX at $6,500 (midpoints, 150 linear ft). Statewide, Coeur d'Alene is 2% above the Idaho figure.

Other Idaho metros

Idaho metros compared with Coeur d'Alene
MetroSizeRangeMidpointvs. here
Boise, ID391,790 jobs$3,600 – $10,800$7,200−1%
Idaho Falls, ID81,840 jobs$3,550 – $10,700$7,100−3%

Cities with a workforce like Coeur d'Alene's

Big cities and small ones price differently, so here is Coeur d'Alene against the 4 metros with the closest total employment.

Metros closest to this one by total employment
MetroSizeRangeMidpointvs. here
Prescott Valley, AZ72,300 jobs$3,550 – $10,800$7,150−2%
Bangor, ME72,270 jobs$3,650 – $11,000$7,300level
Auburn, AL72,710 jobs$3,350 – $10,300$6,800−6%
Bozeman, MT72,210 jobs$3,900 – $11,500$7,700+6%

Local wages behind the labor line

Wages are the part of this estimate that changes most from town to town. 3 trades carry the job here, and each is compared with its US median. The weighted result for Coeur d'Alene is 0.95 times the national level.

For carpenters (47-2031, weighted 40%) the local median is $27.00 an hour, which is 7% below the national $29.12. The middle half of them earn between $23.14 and $30.11 an hour. BLS counts 790 of them working in the area, 109.3 for every 10,000 jobs (US: 43.1), so the local bench is deeper than average.

Construction laborers (47-2061), 40% of the weighting: a median of $24.48 an hour, 8% above the US median of $22.66. The middle half of them earn between $21.40 and $28.20 an hour. About 1,080 work in the metro. That is 149.4 per 10,000 jobs, compared with 70.5 nationally, which suggests plenty of local crews to bid.

Sheet metal workers (47-2211) carry 20% of the labor weighting. BLS does not publish this trade for the Coeur d'Alene metro, so we used the Idaho statewide median: $22.29 an hour against $29.71 for the US. The middle half of them earn between $18.09 and $36.24 an hour.

Quotes come from real crews, not medians. If the carpenters on your job are paid at the 75th percentile ($30.11 an hour) instead of the median, the labor line grows by about $110. At the 25th percentile ($23.14) it shrinks by about $140. The total moves by 1.5% or 1.9%, so wages alone rarely explain a quote that is far outside our range.

For context on the local economy, BLS counts 72,280 jobs in the Coeur d'Alene area. That makes it the 254th largest of the 300 metros we cover, with 0.05% of US employment.

Median hourly wages behind the labor line (BLS OEWS, May 2025)
TradeWeight25th pctMedian75th pctUS medianRatioLevel used
Carpenters (47-2031)40%$23.14$27.00$30.11$29.120.93metro
Construction laborers (47-2061)40%$21.40$24.48$28.20$22.661.08metro
Sheet metal workers (47-2211)20%$18.09$22.29$36.24$29.710.75state
Blended100%0.95

What nearby projects cost in Coeur d'Alene

Because every project leans on different trades, Coeur d'Alene's wage level does not move all prices equally. Against the US midpoint, inground pool runs level and vinyl fence −3%.

Related projects with local prices
ProjectSizeRangevs. US
Vinyl fence150 linear ft$4,400 – $8,900−3%
Wood fence150 linear ft$2,950 – $7,450−3%
Chain-link fence150 linear ft$1,500 – $6,150level
Inground pool450 sq ft$36,100 – $113,000level

Aluminum fence: what moves the price in Coeur d'Alene

  • Permit

    A fence permit runs $40-$150.

  • Style

    Aluminum picket runs $25-$50 per linear foot installed, ornamental fence $40-$75, and privacy designs $75-$130 (HomeGuide).

  • Soil and slope

    Steep slopes and rocky clay can add $15-$20+ per linear foot in labor.

Add-ons priced for Coeur d'Alene

Extras are quoted nationally and then scaled to Coeur d'Alene by the average of the local wage index (0.95) and goods index (0.96), a factor of 0.96. Tick any of them in the estimator above to add them to your total. Treat these as planning figures: an add-on touches different trades than the main job, so the scaling is an approximation.

Add-on prices
Add-onLocal range
Add one gate (flat)$190 – $860

When to schedule aluminum fence in Coeur d'Alene

We use NOAA's 1991-2020 climate normals for Coeur D'Alene (in the city). These are 30-year monthly averages, not forecasts.

March through October is the stretch where exterior installation runs into the fewest weather problems in Coeur d'Alene (8 of 12 months). January, February, November and December have an average daytime high under 45°F.

In January, February, November and December the average high stays below 45°F. Sealants, adhesives and some materials, such as vinyl, are harder to install well in the cold, and short daylight cuts the working day.

Coeur d'Alene gets about 25 inches of precipitation in a normal year. The wettest months are January, November and December (3.5 inches in December). Inside the workable window, July and August are the driest, at 0.7 and 0.8 inches. The station averages about 18 days a year at 90°F or above.

Does the season change the price? Probably, but we do not have a sourced seasonal price curve, so the estimator shows a year-round figure and does not adjust by month. When you collect quotes, ask whether scheduling in a slower month gets a better rate.

Monthly normals, Coeur D'Alene (NOAA, 1991-2020)
MonthAvg high °FAvg low °FPrecip (in)For this job
Jan36263.2Cold
Feb41272.1Cold
Mar48312.7Workable
Apr56371.9Workable
May66442.1Workable
Jun72512.2Workable
Jul83570.7Workable
Aug83560.8Workable
Sep74480.8Workable
Oct58392.0Workable
Nov44323.3Cold
Dec36263.5Cold

Pick a size, pick a tier: aluminum fence pricing in Coeur d'Alene

Three bands are cut from the same cited range and localized for Coeur d'Alene wages and prices. They overlap on purpose: a good standard job and a modest premium job can cost the same. The grid below prices the same bands at 3 common sizes.

Basic

$3,650 to $6,550

Standard picket or ornamental, 4 ft

Standard

$5,800 to $8,750

Ornamental pool-code fence, 4-5 ft

Premium

$8,000 to $10,900

Tall privacy slat or custom ornamental

Cost by size and quality level
SizeBasicStandardPremium
pool fence (100 linear ft)$2,450 – $4,400$3,900 – $5,850$5,400 – $7,350
150 ft (150 linear ft)$3,650 – $6,550$5,800 – $8,750$8,000 – $10,900
200 ft (200 linear ft)$4,850 – $8,700$7,750 – $11,600$10,700 – $14,500

Get 3 local quotes

Tell us about the job and we will try to connect you with up to three local contractors for written quotes. It is free and you are under no obligation to hire. Your estimate of $5,800 to $8,750 for Coeur d'Alene, ID is attached.

Take this estimate with you: PDF report, $9

Multi-page report for Coeur d'Alene, ID: low, typical and high cost, a line-item breakdown of materials and labor by trade, permit notes, the best months to schedule, a quote comparison sheet, red flags, questions for contractors, checklists and every source. Save your estimate above, preview page 1 free, and unlock the full report for $9 one-time, or get every report with CostLocal Pro.

Aluminum fence in Coeur d'Alene: your questions

+How much does it cost to install an aluminum fence in Coeur d'Alene?

For 150 linear ft, expect $3,650 to $10,900 in the Coeur d'Alene area. A standard-spec job lands at $5,800 to $8,750. Small jobs usually cost more per linear ft and large ones less.

+What is the price per linear ft for aluminum fence in Coeur d'Alene?

About $24 to $72 per linear ft for materials and labor, plus $40 to $150 for the permit if one is needed. The US range is $25 to $75.

+Is aluminum fence cheaper in Coeur d'Alene or Spokane?

Spokane is 55 miles away. The midpoint for 150 linear ft there is $8,050, which is 11% more than Coeur d'Alene ($7,300). Wage and materials indexes both feed that gap.

+How much of the bill is labor in Coeur d'Alene?

About 34% at the midpoint, or $2,500 out of $7,300. Materials are 64% and permits 1%. Nationally, labor is 35%.

+What would 150 ft (150 linear ft) cost in Coeur d'Alene?

$3,650 to $10,900. Pick a different size in the estimator above to get your own number.

+Does aluminum fence need a permit in Coeur d'Alene?

Often, but rules are set by your city or county building office, so call before you hire. Budget $40 to $150 for fees in the Coeur d'Alene area (our national range of $40 to $150 scaled by the local price level).

+Is Coeur d'Alene expensive for aluminum fence compared with the rest of Idaho?

Coeur d'Alene is 2% above the Idaho statewide estimate ($7,150 at the midpoint). We cover 3 metros in Idaho; see the state page to compare them.

+What do carpenters earn in Coeur d'Alene?

The BLS median is $27.00 an hour in the Coeur d'Alene area, compared with $29.12 nationally. The 25th to 75th percentile range is $23.14 to $30.11.

+What do basic and premium aluminum fence work cost in Coeur d'Alene?

For 150 linear ft, basic work runs $3,650 to $6,550 and premium work $8,000 to $10,900. Basic means: standard picket or ornamental, 4 ft. Premium means: tall privacy slat or custom ornamental.

+When is the best time to install an aluminum fence in Coeur d'Alene?

Based on NOAA 1991-2020 normals, the comfortable months for this kind of work are March through October. July and August are typically the driest of those months. Local contractors' schedules matter as much as the weather, so book early for the busy months.

+What does "add one gate" add in Coeur d'Alene?

$190 to $860, from a national range scaled by the local wage and goods indexes.

Aluminum fence near Coeur d'Alene

Aluminum fence: all pricesAluminum fence in IdahoAll projects in Coeur d'AleneIdaho cost hub

Where these numbers come from

Base prices are national ranges from the sources below. We scale labor by local BLS wages, materials by BEA goods prices and permits by the BEA all-items price level. Full method on the methodology page.

Note on derived figures: Materials = installed range minus HomeGuide's $10-$25/ft labor range.